boards: nxp: frdm_rw612: restructure dts

Restructure board dts file to prepare for NS targets using common dts. Signed-off-by: David Leach <[email protected]>
zephyrproject-rtos · Dec 9, 2024 · 259302a · 259302a
1 parent 9cdb07c
commit 259302a
Show file tree

Hide file tree

Showing 2 changed files with 223 additions and 216 deletions.
diff --git a/boards/nxp/frdm_rw612/frdm_rw612.dts b/boards/nxp/frdm_rw612/frdm_rw612.dts
@@ -7,219 +7,4 @@
 /dts-v1/;
 
 #include <nxp/nxp_rw6xx.dtsi>
-#include "frdm_rw612-pinctrl.dtsi"
-
-/ {
-	model = "nxp,frdm_rw612";
-
-	aliases {
-		led0 = &green_led;
-		watchdog0 = &wwdt;
-		usart-0 = &flexcomm3;
-		i2c-0 = &flexcomm2;
-		pwm-0 = &sctimer;
-	};
-
-	chosen {
-		zephyr,sram = &sram_data;
-		zephyr,flash = &w25q512jvfiq;
-		zephyr,console = &flexcomm3;
-		zephyr,shell-uart = &flexcomm3;
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		green_led: led_1 {
-			gpios = <&hsgpio0 12 0>;
-		};
-	};
-};
-
-&flexcomm3 {
-	compatible = "nxp,lpc-usart";
-	status = "okay";
-	current-speed = <115200>;
-	pinctrl-0 = <&pinmux_flexcomm3_usart>;
-	pinctrl-names = "default";
-};
-
-&flexcomm0 {
-	compatible = "nxp,lpc-usart";
-	status = "disabled";
-	current-speed = <115200>;
-	pinctrl-0 = <&pinmux_flexcomm0_usart>;
-	pinctrl-names = "default";
-};
-
-&hsgpio0 {
-	status = "okay";
-};
-
-&flexspi {
-	status = "okay";
-	ahb-bufferable;
-	ahb-prefetch;
-	ahb-cacheable;
-	ahb-read-addr-opt;
-	ahb-boundary = "1024";
-	rx-clock-source = <1>;
-	rx-clock-source-b = <1>;
-	/* Winbond external flash */
-	w25q512jvfiq: w25q512jvfiq@0 {
-		compatible = "nxp,imx-flexspi-nor";
-		reg = <0>;
-		size = <DT_SIZE_M(64 * 8)>;
-		status = "okay";
-		erase-block-size = <4096>;
-		write-block-size = <1>;
-		spi-max-frequency = <104000000>;
-
-		partitions {
-			compatible = "fixed-partitions";
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			boot_partition: partition@0 {
-				label = "mcuboot";
-				reg = <0x00000000 DT_SIZE_K(128)>;
-			};
-			/* The MCUBoot swap-move algorithm uses the last 2 sectors
-			 * of the primary slot0 for swap status and move.
-			 */
-			slot0_partition: partition@20000 {
-				label = "image-0";
-				reg = <0x00020000 (DT_SIZE_M(3) + DT_SIZE_K(2 * 4))>;
-			};
-			slot1_partition: partition@323000 {
-				label = "image-1";
-				reg = <0x00323000 DT_SIZE_M(3)>;
-			};
-			storage_partition: partition@623000 {
-				label = "storage";
-				reg = <0x00623000 (DT_SIZE_M(58) - DT_SIZE_K(136))>;
-			};
-		};
-	};
-	aps6404l: aps6404l@2 {
-			compatible = "nxp,imx-flexspi-aps6404l";
-			/* APS6404L is 8MB, 64MBit pSRAM */
-			size = <DT_SIZE_M(8 * 8)>;
-			reg = <2>;
-			spi-max-frequency = <109000000>;
-			/* PSRAM cannot be enabled while board is in default XIP
-			 * configuration, as it will conflict with flash chip.
-			 */
-			status = "disabled";
-			cs-interval-unit = <1>;
-			cs-interval = <2>;
-			cs-hold-time = <3>;
-			cs-setup-time = <3>;
-			data-valid-time = <6>;
-			column-space = <0>;
-			ahb-write-wait-unit = <2>;
-			ahb-write-wait-interval = <0>;
-	};
-};
-
-&hci {
-	status = "okay";
-	wakeup-source;
-};
-
-&enet_mac {
-	status = "okay";
-	pinctrl-0 = <&pinmux_enet>;
-	pinctrl-names = "default";
-	phy-handle = <&phy>;
-	zephyr,random-mac-address;
-	phy-connection-type = "rmii";
-};
-
-&enet_mdio {
-	status = "okay";
-	pinctrl-0 = <&pinmux_mdio>;
-	pinctrl-names = "default";
-	phy: phy@2 {
-		compatible = "microchip,ksz8081";
-		reg = <2>;
-		status = "okay";
-		reset-gpios = <&hsgpio1 23 GPIO_ACTIVE_HIGH>;
-		int-gpios = <&hsgpio0 21 GPIO_ACTIVE_HIGH>;
-		microchip,interface-type = "rmii";
-	};
-};
-
-&wwdt {
-	status = "okay";
-};
-
-&dma0 {
-	status = "okay";
-};
-
-&mrt0_channel0 {
-	status = "okay";
-};
-
-&ctimer0 {
-	status = "okay";
-};
-
-&pmu {
-	reset-causes-en = <PMU_RESET_CM33_LOCKUP>,
-			  <PMU_RESET_ITRC>,
-			  <PMU_RESET_AP_RESET>;
-};
-
-/* OS Timer is the wakeup source for PM mode 2 */
-&os_timer {
-	status = "okay";
-	wakeup-source;
-};
-
-&systick {
-	status = "disabled";
-};
-
-&adc0 {
-	status = "okay";
-};
-
-&dac0 {
-	status = "okay";
-};
-
-&sctimer {
-	status = "okay";
-	pinctrl-0 = <&pinmux_pwm0>;
-	pinctrl-names = "default";
-};
-
-zephyr_udc0: &usb_otg {
-	status = "okay";
-};
-
-/*
- * the default resistors on the board breaks out the MOSI/MISO
- * pins to the nets labelled "UART" which go to J1 2 and 4,
- * but we are using it for spi mosi and miso here.
- * SCK is on J2 6 as labelled.
- */
-&flexcomm1 {
-	compatible = "nxp,lpc-spi";
-	pinctrl-0 = <&pinmux_flexcomm1_spi>;
-	pinctrl-names = "default";
-	status = "okay";
-	#address-cells = <1>;
-	#size-cells = <0>;
-};
-
-arduino_i2c: &flexcomm2 {
-	compatible = "nxp,lpc-i2c";
-	status = "okay";
-	clock-frequency = <I2C_BITRATE_FAST>;
-	#address-cells = <1>;
-	#size-cells = <0>;
-	pinctrl-0 = <&pinmux_flexcomm2_i2c>;
-	pinctrl-names = "default";
-};
+#include "frdm_rw612_common.dtsi"