INAV MSP frames changelog

INAV 1.6 MSP API Version 1.24

MSP_NAV_POSHOLD

Basic position hold settings. Mostly, but not only, for multirotor

Frame IDs:

• MSP_NAV_POSHOLD, Frame ID 12
• MSP_SET_NAV_POSHOLD, Frame ID 13

Length	Setting	Notes
1	nav_user_control_mode	dictionary
2	nav_max_speed
2	nav_max_climb_rate
2	nav_manual_speed
2	nav_manual_climb_rate
1	nav_mc_bank_angle
1	nav_use_midthr_for_althold	ON/OFF
2	nav_mc_hover_thr
8	reserved

INAV 1.5 MSP API Version 1.23

For iNav 1.5 and later, the MSP_STATUS/sensor field reports sensor failure. This updates MSP_SENSOR (see http://www.multiwii.com/wiki/index.php?title=Multiwii_Serial_Protocol) in a backwards compatible manner to report additional sensors and sensor health. The sensor field is reported as:

Bit	Usage
0	Set if ACC present
1	Set if BARO present
2	Set if MAG present
3	Set if GPS present
4	Set if SONAR present
5	Reserved for OPFLOW (not implemented)
6	Set if PITOT present
15	Set on sensor failure

The sensor hardware failure indication is backwards compatible with versions prior to 1.5 (and other Multiwii / Cleanflight derivatives).

MSP_SENSOR_CONFIG

Frame IDs:

• MSP_SENSOR_CONFIG, Frame ID 96
• MSP_SET_SENSOR_CONFIG, Frame ID 97

length	setting	Notes
1	acc_hardware
1	baro_hardware
1	mag_hardware
1	pitot_hardware
1	Reserved for rangefinder	not yet implemented
1	Reserved for OpFlow	not yet implemented

INAV 1.4 MSP API Version 1.22

MSP_INAV_PID

Frame IDs:

• MSP_INAV_PID, Frame ID 6
• MSP_SET_INAV_PID, Frame ID 7

length	setting	Notes
1	async_mode
2	acc_task_frequency
2	attitude_task_frequency
1	mag_hold_rate_limit
1	MAG_HOLD_ERROR_LPF_FREQ	not implemented yet as configurable
2	yaw_jump_prevention_limit
1	gyro_lpf
1	acc_soft_lpf_hz
4	reserved	reserved for further usage

MSP_FILTER_CONFIG

Compatible with Betaflight

Frame IDs:

• MSP_FILTER_CONFIG Frame ID 92
• MSP_SET_FILTER_CONFIG Frame ID 93

length	setting	Notes
1	gyro_soft_lpf_hz
2	dterm_lpf_hz
2	yaw_lpf_hz
2	gyro_soft_notch_hz	Betaflight masterConfig.gyro_soft_notch_hz_1
2	gyro_soft_notch_cutoff_hz	Betaflight masterConfig.gyro_soft_notch_cutoff_1
2	not used	Betaflight pidProfile.dterm_notch_hz
2	not used	Betaflight pidProfile.dterm_notch_cutoff
2	not used	Betaflight masterConfig.gyro_soft_notch_hz_2
2	not used	Betaflight masterConfig.gyro_soft_notch_cutoff_2

MSP_PID_ADVANCED

Compatible with Betaflight

Frame IDs:

• MSP_PID_ADVANCED Frame ID 94
• MSP_SET_PID_ADVANCED Frame ID 95

length	setting	Notes
2	rollPitchItermIgnoreRate
2	yawItermIgnoreRate
2	yaw_p_limit
1	not used	Betaflight deltaMethod
1	not used	Betaflight vbatPidCompensation
1	not used	Betaflight setpointRelaxRatio
1	not used	Betaflight dtermSetpointWeight
1	reserved
1	reserved
1	not used	Betaflight itermThrottleGain
2	rate_accel_limit_roll_pitch	divided by 10
2	rate_accel_limit_yaw	divided by 10

INAV 1.3 MSP API 1.21

case MSP_ADVANCED_CONFIG:

Frame IDs:

• MSP_ADVANCED_CONFIG, Frame ID 90
• MSP_SET_ADVANCED_CONFIG, Frame ID 91

length	setting	Notes
1	gyro_sync_denom
1	not used	Betaflight masterConfig.pid_process_denom
1	not used	Betaflight masterConfig.motorConfig.useUnsyncedPwm
1	motor_pwm_protocol	dictionary
2	motor_pwm_rate
2	servo_pwm_rate
1	gyro_sync	boolean

##Change log:

• 2016-11-20 - scaling of rate_accel_limit_roll_pitch and rate_accel_limit_yaw in MSP_PID_ADVANCED changed from 1000 to 10
• 2016-12-11 - added MSP_STATUS update for iNav 1.5