Linux Container with Xilinx Vivado/Vivado HLS

For many reasons having Xilinx Vivado/Vivado HLS installed in a docker image can be useful. This package is setup to build docker images with various setups using the CERN GitLab docker-builder runners. The configurations for the docker builds can be found in the table below:

Linux Flavor	Vivado Version	X11	VNC	Status
Ubuntu 18.04	2019.1	Yes	Yes
SL7	2018.2	Yes	No
SL7	2019.1	Yes	No
SL7	2019.2	Yes	No

The Ubuntu version features both X11 and VNC and is generally less secure. The Scientific Linux (SL) container was built with security in mind. It is meant to conform with the security policies laid out by Fermi National Accelerator Laboratory (FNAL).

The general idea behind these containers was that they would be transient and always run with the --rm option. Any external files that needed to be used within the container could be mapped using a shared folder (i.e. -v <path to host folder>:<path in container>). I never intended, nor have I tested, ssh'ing into the containers. This tends to open up security holes (i.e. root access, passwords, internal vs external port connections) that I didn't want to deal with.

In general, however, it's best to lock down docker so that ssh to the remote machine is only accessible from your local machine. To do this, you can use the option -p 127.0.0.1:22:22 when doing the ssh command (not -P). Alternatively, you can go to the docker settings and change the default to always listen only on the local interface. Go to Preferences... > Daemon > Advanced and add the lines:

{
    "ip" : "127.0.0.1"
}

Build Instructions

This repository was designed for the containers to be built using the CI/CD system of CERN's GitLab instance. The primary reason for this is that the Xilinx Vivado installation file is hosted on CERNBox and therefore the fastest connection to a build system will be at CERN.

Using the recommended method, once changes are pushed to the GitHub repository, they are synchronized with the GitLab instance (manually or automatically) and then a CI/CD pipeline is triggered manually. From there is it just a matter of time before the containers are ready, ~1.5 hours is all is successful.

Still, it is possibly to build the system somewhere other than a CERN runner. Because you will no longer be using Kaniko, the docker build will have to be configured manually. This might also result in a larger image file because of different cleanup and cache settings. The commands to run are as follows:

docker login -u <CERN SSO Username> -p <CERN SSO Password> gitlab-registry.cern.ch
docker build --pull -t <username>/vivado-docker/<container name>:<container tag> <relative path to Dockerfile>
docker push <username>/vivado-docker/<container name>:<container tag>

Note: The container image name must contain only lowercase letters.

Run Using X11

This is my preferred way of accessing the remote windows. For one, it requires fewer additions to the base operating system. Additionally, it's easier to resize the windows, not having to set the geometry when running the container. That being said, some care must be taken to secure the connection between the remote system and the localhost.

Directly Connect Host and Remote

These directions will assume that the user is running OSX and has XQuartz installed. Settings for other host systems and/or X11 window programs are left to the user to figure out.

This next step only has to be performed once for the host system. We will need to make sure that XQuartz allows connections from network/remote clients. Open the menu at XQuartz > Preferences... and click on the Security tab. Make sure that the check box next to "Allow connections from network clients" is selected. You will need to restart XQuartz if this option wasn't already enabled.

Add the local interface to the list of acceptable connections by doing xhost + 127.0.0.1. This needs to be done only when the xhost list is reset. I'm not sure when this is (i.e. upon restart?).

To open the remote program and start an x-window use the command:

docker run --rm -it --net=host -e DISPLAY=host.docker.internal:0 gitlab-registry.cern.ch/aperloff/vivado-docker/<container name>:<container tag> /opt/Xilinx/Vivado/2019.1/bin/vivado

Note: You may need to do docker login gitlab-registry.cern.ch in order to pull the image from GitLab. Use your CERN username and password.

Use the System IP Address

This is a less secure method of connecting the remote program to the X11 system on the host. This is because you are allowing the remote system to access the internet and then connect to your system's external IP address. While the xhost command does limit the connections to just that one address, this is still note the best practice and may get you booted off the network at FNAL.

IP=$(ifconfig en0 | grep inet | awk '$1=="inet" {print $2}')  # use en1 for Wifi
xhost + $IP
docker run --rm -it -e DISPLAY=$IP:0 -v /tmp/.X11-unix:/tmp/.X11-unix gitlab-registry.cern.ch/aperloff/vivado-docker/<container name>:<container tag> /opt/Xilinx/Vivado/2019.1/bin/vivado

Note: I found that at one point I needed to reset my xhost list by turning off the xhost filtering and then turning it back on xhost <-/+>. At FNAL, remember to disconnect from the internet before you do this because it will be seen as opening up a hole in your firewall and get you blocked from the network.

Alternate Entrypoint

To override the entrypoint, you need to use the --entrypoint option. You may want to do this, for instance, if you want to open a bash terminal rather than Vivado directly.

docker run --rm -it -e DISPLAY=$IP:0 -v /tmp/.X11-unix:/tmp/.X11-unix --entrypoint /bin/bash gitlab-registry.cern.ch/aperloff/vivado-docker/<container name>:<container tag>

xilinx_docker Bash Function

Inside the file .xilinx_docker there is a bash function named xilinx_docker. This function is meant to help the user quickly spin up a one of these docker containers. Rather than having to remember the entire docker run command and the variations for each entrypoint, this function provides a much simpler interface. It is based on the "Direct Connection" method mentioned above. I find it useful to source the .xilinx_docker file from within my login script.

For a complete set of directions on how to use this utility, see the functions help message. Simply use:

xilinx_docker -h

Run Using VNC

VNC is not my favorite way to interact with remote programs. Resizing of windows always seems haphazard. That being said, the Ubuntu version of this container was built with VNC available. To run it, use the command:

docker run --rm -ti -p 5900:5900 -v `pwd`/work:/home/vivado/ -e GEOMETRY=1920x1200 gitlab-registry.cern.ch/aperloff/vivado-docker/<container name>:<container tag>

You will be asked to enter a 6+ character password for the VNC server. Then on the host machine use the following command to connect to the VNC server on the container:

open vnc://127.0.0.1:5900

CU Specific Running Instructions

In order to access the CU Vivado license it may be necessary to set an environment variable when running the docker container using -e [email protected]:[email protected]

Command Line Access to a Currently Running Container

If you need to access the command line for a container which is currently running you can use the following command to open up a bash prompt:

docker exec -it <container name> bash

You may need to run docker ps -a to find the name of the container if you didn't set one yourself. Docker will set it's own name if you didn't specify one.