fix for esp32S3_4MB_PSRAM builds (S3 zero and supermini)

platformio.ini

@@ -2160,6 +2160,8 @@ extends = env:esp32S3_8MB_S
 board = lolin_s3_mini ;; -S3 mini: 4MB flash 2MB PSRAM 
 board_build.partitions = tools/WLED_ESP32_4MB_256KB_FS.csv   ;; 1.8MB firmware, 256KB filesystem (esptool erase_flash needed when changing from "standard WLED" partitions)
 ;; board_build.partitions = tools/WLED_ESP32_4MB_512KB_FS.csv    ;; 1.7MB firmware, 500KB filesystem (esptool erase_flash needed when changing from "standard WLED" partitions)
+build_unflags = ${common.build_unflags}
+  -D WLED_ENABLE_HUB75MATRIX ;; board does not have enough pins for HUB75
 build_flags = ${common.build_flags} ${esp32s3.build_flags} -Wno-misleading-indentation -Wno-format-truncation
   ${common_mm.build_flags_S}
   -D WLED_RELEASE_NAME=esp32S3_4MB_PSRAM_S
@@ -2188,16 +2190,23 @@ build_flags = ${common.build_flags} ${esp32s3.build_flags} -Wno-misleading-inden
   ; -D WLED_DEBUG
   ; -D SR_DEBUG
   ; -D MIC_LOGGER
+lib_deps = ${esp32s3.lib_deps} ${common_mm.lib_deps_S}  ${common_mm.lib_deps_V4_M}
+    ${common_mm.animartrix_lib_deps}
 lib_ignore =
   IRremoteESP8266 ; use with WLED_DISABLE_INFRARED for faster compilation
-; RAM:   [==        ]  20.4% (used 66908 bytes from 327680 bytes)
-; Flash: [========= ]  87.1% (used 1655529 bytes from 1900544 bytes)
+  ${common_mm.HUB75_lib_ignore}
+  ${common_mm.DMXin_lib_ignore}
+; RAM:   [==        ]  18.6% (used 60828 bytes from 327680 bytes)
+; Flash: [========  ]  76.9% (used 1461829 bytes from 1900544 bytes)
 
 ;; MM for esp32-s3 zero/supermini and lolin S3 mini boards - standard
 [env:esp32S3_4MB_PSRAM_M]
 extends = env:esp32S3_8MB_M
 board = lolin_s3_mini ;; -S3 mini: 4MB flash 2MB PSRAM 
 board_build.partitions = ${esp32.default_partitions}
+build_unflags = ${common.build_unflags}
+  -D WLED_ENABLE_HUB75MATRIX ;; board does not have enough pins for HUB75
+  -D USERMOD_ANIMARTRIX ;; not enough flash
 build_flags = ${common.build_flags} ${esp32s3.build_flags} -Wno-misleading-indentation -Wno-format-truncation
   ${common_mm.build_flags_S} ${common_mm.build_flags_M}
   -D WLED_RELEASE_NAME=esp32S3_4MB_PSRAM_M
@@ -2208,7 +2217,7 @@ build_flags = ${common.build_flags} ${esp32s3.build_flags} -Wno-misleading-inden
   -DARDUINO_USB_MODE=1 -DARDUINO_USB_CDC_ON_BOOT=0 -DARDUINO_USB_MSC_ON_BOOT=0 -DARDUINO_USB_DFU_ON_BOOT=1   ;; for Serial-to-USB chip
   ;;-DARDUINO_USB_MODE=1 -DARDUINO_USB_CDC_ON_BOOT=1 -DARDUINO_USB_MSC_ON_BOOT=0 -DARDUINO_USB_DFU_ON_BOOT=1 ;; for Hardware-CDC USB mode
   -D WLED_DISABLE_ADALIGHT    ;; disables serial protocols - recommended for Hardware-CDC USB (Serial RX will receive junk commands when RX pin is unconnected, unless its pulled down by resistor)
-  ${common_mm.animartrix_build_flags}
+  ;; ${common_mm.animartrix_build_flags} ;; not enough flash
   -D LEDPIN=21
   -D BTNPIN=-1 -D RLYPIN=-1 -D IRPIN=-1 -D AUDIOPIN=-1
   -D HW_PIN_SDA=12 -D HW_PIN_SCL=13
@@ -2225,8 +2234,11 @@ build_flags = ${common.build_flags} ${esp32s3.build_flags} -Wno-misleading-inden
 lib_deps = ${esp32s3.lib_deps} ${common_mm.lib_deps_S}  ${common_mm.lib_deps_V4_M}
 lib_ignore =
   IRremoteESP8266 ; use with WLED_DISABLE_INFRARED for faster compilation
-; RAM:   [==        ]  20.6% (used 67532 bytes from 327680 bytes)
-; Flash: [==========]  98.4% (used 1547445 bytes from 1572864 bytes)
+  ${common_mm.HUB75_lib_ignore}
+  ${common_mm.DMXin_lib_ignore}
+  ${common_mm.animartrix_lib_ignore}
+; RAM:   [==        ]  18.7% (used 61172 bytes from 327680 bytes)
+; Flash: [==========]  97.7% (used 1536157 bytes from 1572864 bytes)
 
 
 # ------------------------------------------------------------------------------