Read ALL of the sections below to understand your hardware requirements, there's some bits here that aren't on a standard Voron build BOM. The chances are that something was missed, but if you have a good mix of M2, M2.5 and M3 hardware you'll probably still end up with a working printer.
| Qty | Item | Notes |
|---|---|---|
| 5 | M3 Heatset Insert | Standard Voron spec: 5mm Outer Diameter x 4mm Length |
| 6 | M3 x 8 SHCS | 4x MGN carriage mounting, 2x MGN carriage clamps |
| 4 | M3 Hex Nut | 2x MGN carriage clamps, 2x toolhead mounting |
| 2 | M3 DIN9021 flat washer | MGN Carriage clamping. Alternatively use M3 + M5 stacked washers |
| 2 | M3 x 30 Pin | Belt mounting system |
| 2 | Hollow metal tube: 4mm OD, 3.1 to 3.2mm ID, 22 to 22.5mm length. | 4mm OD, 0.45mm wall width (0.4mm wall width is OK). Stainless steel, brass, aluminium all tested OK. Used for belt mounting system.4mm OD/3mm ID PTFE tube can be used temporarily |
| 2 | 1.8mm wide cable tie or 0.5mm solid core wire | To attach M4 tube to belt clips as per Archetype clips |
Follow probe or extruder instructions for required hardware.
* If using Voron Design TAP RC8+ it is recommended to replace the two M3 x 50 SHCS with M3 x 50 BHCS to improve build plate clearance.
| Qty | Item | Notes |
|---|---|---|
| 3* | M3 Heatset Insert | Standard Voron spec: 5mm Outer Diameter x 4mm Length * Extruder Mount 3rd heatset for extruders with additional front screw |
| 3 | M3 Hex Nut | 2x Extruder Mount 1x Hotend Mount mount below front of Extruder Block |
| 2 | M3 x 20 Metal Stand-off | CAN/EBB Mounting |
| 2 | M3 x [20][8] SHCS | Extruder to HE Mount. Length varies depending on extruder used M3x20 used for Sherpa-Mini, M3x8 used for most others |
| 6 | M3 x 16 SHCS | 2x Through Extruder and hotend mounts to carriage 2x Extruder stepper to standoff 2x CAN/EBB36 mount |
| 7 | M3 x 8 SHCS | 2x HE Mount feet, 2x HE Adapter to carriage, 2x MGN carriage clamping, 1x EBB Mount |
| 2* | M3 x 6 BHCS | Extruder Mount to Hotend Mount at front. *additional 1 if using extruder with front faceplate that includes extra point. |
| 4 | M2.5 x 16 SHCS | HE Fan |
| 4 | M2.5 x 8 SHCS | Part cooling fan mounting |
| 4* | M2.5 x 8 SHCS | *additional to above if using XolPAP ducts |
| 1 | Short PTFE tube | Between extruder and hotend |
ℹ️ Understand your electronics and voltages
Do you have the correct voltage at your toolhead or will you need a converter?
If using the recommended parts you need 5v, 12v and 24v at the toolhead.
| Qty | Fan Type | Recommended Fan | Notes |
|---|---|---|---|
| 1 | 2510 Axial Fan Hotend Fan |
Delta Electronics 5v ASB02505SHA-AY6B |
Purchase Link This fan is highly recommended in heated chambersNo other 2510 fan comes close to the performanceof this fan. |
| 2 | 4010 Blower Fan Part Cooling Fans |
Delta Electronics BFB0412HHA-A (12V) Purchase Link BFB0405HHA-A (5V) Purchase Link |
24v GDStime fans are fine and many have used them successfully.The Deltas, however, have better durabilityin heated chambers and always hit their performance claims.It's not uncommon for other fan manufacturersto overstate performance, GDStime included. |
| 1* | 7040 or other suitable CPAP remote cooling fan | XolPAP only | |
| 1* | 15mm ID CPAP flexible hose | XolPAP only |
Additional notes: Delta's 5V and 12V variants provide the same airflow, pick whichever suits your setup better. If you only have 24V available, you can use a 24V-12V buck converter or run an additional wire in your umbilical for 12v+.
| Qty | Item | Notes |
|---|---|---|
| 1 | M3 Heatset Insert | Sherpa-Mini and G2 / WristWatch front plate attachment |
| 1 | M3 Heatset Insert | DFA Custom bottom |
| 2 | M2 x 10 self tapping screws | X End stop |
| 1 | LED harness | 1x RGB Neopixel LEDs, and 2x RGB Sequin LEDs (0.8mm board thickness) 26 or 28 AWG wire. Build instructions Only compatible with the thin PCB board sequins.Known working sources:RGBW: LAB4450 (EU) RGBW: Replimat[labs] (EU) RGBW: JB3D.uk (UK) RGB: FYSETC (Ali Express) |
⬅ README - Printed Parts ➡