Replies: 6 comments
-
Standard question: which version of the GUI and firmware are you using?
Can you add some details here please? My best guess is that you mean a SCPI command. |
Beta Was this translation helpful? Give feedback.
-
Thank you very much for your anwser.
Here is the sofware we use :
Also when I lunch the cal section here is the message : the call never starts !
We are unable fo find out the problem occuring on many computers.
Regards
Fabien NDAGIJIMANA
Professeur Université de Grenoble
IUT1 - Chef dépt Génie Electrique et Informatique Industrielle
Laboratoire G2Elab (UMR 5269) / Plateforme RF&CEM Pheline
Tel 06 19 07 01 85
De: "jankae" ***@***.***>
À: "jankae/LibreVNA" ***@***.***>
Cc: "'fabien ndagijimana" ***@***.***>, "Author" ***@***.***>
Envoyé: Vendredi 3 Mars 2023 19:43:55
Objet: Re: [jankae/LibreVNA] Communication with Libre VNA (Discussion #197)
Standard question: which version of the GUI and firmware are you using?
the "meas" on calibration steps does not respond.
Can you add some details here please? My best guess is that you mean a SCPI command.
—
Reply to this email directly, [ #197 (comment) | view it on GitHub ] , or [ https://github.com/notifications/unsubscribe-auth/A6IDG3DRLRYY4EA3U7WAIT3W2I3WXANCNFSM6AAAAAAVOW4HMU | unsubscribe ] .
You are receiving this because you authored the thread. Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
Sorry, I don't see any program version in your message. Did you try to attach screenshots? Not sure how that is handled by Github when you reply by mail. Please try responding through the Github user interface. |
Beta Was this translation helpful? Give feedback.
-
Now I have found : the version we use is 1.3
We try to update with 1.4 or 1.5 but we have no idea of the issue with USB connection.
Cordialement
Fabien NDAGIJIMANA
Professeur Université de Grenoble
IUT1 - Chef dépt Génie Electrique et Informatique Industrielle
Laboratoire G2Elab (UMR 5269) / Plateforme RF&CEM Pheline
Tel 06 19 07 01 85
De: "jankae" ***@***.***>
À: "jankae/LibreVNA" ***@***.***>
Cc: "'fabien ndagijimana" ***@***.***>, "Author" ***@***.***>
Envoyé: Mercredi 8 Mars 2023 19:44:09
Objet: Re: [jankae/LibreVNA] Communication with Libre VNA (Discussion #197)
Sorry, I don't see any program version in your message. Did you try to attach screenshots? Not sure how that is handled by Github when you reply by mail. Please try responding through the Github user interface.
—
Reply to this email directly, [ #197 (comment) | view it on GitHub ] , or [ https://github.com/notifications/unsubscribe-auth/A6IDG3GY6TFQU2GAXDWEMHLW3DHPTANCNFSM6AAAAAAVOW4HMU | unsubscribe ] .
You are receiving this because you authored the thread. Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
Yes please update, 1.3.0 is rather old. I am not sure what you mean by "issue with USB connection". Is this still the same issue you originally mentioned? Is your GUI able to find the device at all? |
Beta Was this translation helpful? Give feedback.
-
I have the similar issue. The GUI cannot find the device. |
Beta Was this translation helpful? Give feedback.
-
My libre VNAs can not run on my computers with Windows 10. We checked all possible reasons like firewall, or admin rights on computers, the "meas" on calibration steps does not respond.
Have you an idea of how to troubleshoot this USB communication issue ?
Note : on computers with Windows 10 "family" there is no problem.
Beta Was this translation helpful? Give feedback.
All reactions