Delay in steam.py #77
Comments
|
If u follow his method for streaming u will have stream without any delays
…On Thu 15 Mar, 2018, 8:31 AM rajaa1996, ***@***.***> wrote:
I get too much delay during streaming of video a lag of about 20sec i use
vncserver chrome extension is there any other way to stream or changes to
make the delay small
—
You are receiving this because you are subscribed to this thread.
Reply to this email directly, view it on GitHub
<#77>, or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJuiWSv2K2BHVO0MTw6xv5AzN0F7g8ks5tedmPgaJpZM4Sre9H>
.
|
|
I did the same as mentioned in this repository but I dono how to stream to my pc using which software |
|
U dont have to use any software
Just python
Go to test folder from ur pc
And under stream_test edit the ip to your computer's ip, 4000 as port
And paste the raspberry pi folder in ur raspberry pi
And open stream python file and change the ip your computer 's Ip and same
port number (4000) for that to work
Note: both. py will have your computer' s ip and both your computer and
raspberry pi should be in same network (same wifi)
After this run the py file first in ur Computer then on your pi
…On Thu 15 Mar, 2018, 8:57 AM rajaa1996, ***@***.***> wrote:
I did the same as mentioned in this repository but I dono how to stream to
my pc using which software
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJum28w7BI7yOddPLPn77M1DJ_cbfmks5ted-xgaJpZM4Sre9H>
.
|
|
Tysm ?!!great man!!!! |
|
Works fine now?????
…On Thu 15 Mar, 2018, 9:33 AM rajaa1996, ***@***.***> wrote:
Tysm ?!!great man!!!!
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJumk6EIUC42c7gu731uBSVRUTqvydks5teegNgaJpZM4Sre9H>
.
|
|
Where should I run rc_driver.py on my computer or on my raspberry pi |
|
Computer
The file in 'computer' should be run in computer
The files in' raspberry pi 'should be run on pi
…On Thu 15 Mar, 2018, 9:34 AM rajaa1996, ***@***.***> wrote:
Where should I run rc_driver.py on my computer or on my raspberry pi
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJuujI8yl0fjClDg4QqOHsFdoIDcg2ks5teehLgaJpZM4Sre9H>
.
|
|
I copied my the computer folder on my pc then how should I run can u tell me little in detail plz |
|
Did u flash the arduino file to your arduino and connect it to the RC car's
remote??
…On Thu 15 Mar, 2018, 9:40 AM rajaa1996, ***@***.***> wrote:
I copied my the computer folder on my pc then how should I run can u tell
me little in detail plz
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJutrx0-9Ri-JK4JuhGkHeP-1mVKgwks5teenDgaJpZM4Sre9H>
.
|
|
I used l293d connected to arduibo nano then connect it to my raspberry pi |
|
I control via my PCs keyboard |
|
Can u send me your project files and details??
…On Thu 15 Mar, 2018, 9:48 AM rajaa1996, ***@***.***> wrote:
I control via my PCs keyboard
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJun_ne4wyOROdn64_jiwe7gv8jOP7ks5teeungaJpZM4Sre9H>
.
|
|
@Goose1909 |
|
@rajaa1996
Thats same as of hamuchiwa's
The reason i tried to send string via socket was i couldn't able to
interface RC remote to arduino
Cos i couldn't find correct points
Thats why
Anyone wanna help me with that problem
…On Thu 15 Mar, 2018, 8:12 PM rajaa1996, ***@***.***> wrote:
@Goose1909 <https://github.com/goose1909>
Check this post
https://github.com/sidroopdaska/SelfDrivingRCCar/blob/master/README.md
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJut-h0fM0OUR7mbEh5QqQ7quf83X6ks5ten25gaJpZM4Sre9H>
.
|
|
I have some prob can u give ur mail id so that I can contact u |
|
… On Fri 16 Mar, 2018, 7:59 AM rajaa1996, ***@***.***> wrote:
I have some prob can u give ur mail id so that I can contact u
—
You are receiving this because you commented.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJugNTQqvLnt5E-oDbXFynxoGsKoNhks5teyNtgaJpZM4Sre9H>
.
|
|
hello @rajaa1996 I would like to have some question, can you contact me plz? my email: [email protected] |
|
@Gooose1909 can you advise me on training the model? my car just keep going left ..... |
|
@Gooose1909 How to select port ? Or any port number is fine? How you chose 4000? |
|
You can select any number for port .
I prefer 4000 and 4001
If you want u cant select 5000 too
…On Sat 23 Mar, 2019, 19:05 ShwetaLalwani, ***@***.***> wrote:
@Gooose1909 <https://github.com/Gooose1909> How to select port ? Or any
port number is fine? How you chose 4000?
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJumPfCl_NKalgD67BmwIgOUfp0It5ks5vZi2EgaJpZM4Sre9H>
.
|
|
I faced the same issue i just made my own RC car fixed everything
…On Wed 6 Mar, 2019, 21:56 kxrf97, ***@***.***> wrote:
@Gooose1909 <https://github.com/Gooose1909> can you advise me on training
the model? my car just keep going left .....
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJuhvlrydHHNv928SWJ4MmN0_MnqP8ks5vT-wygaJpZM4Sre9H>
.
|
|
Thanks.. |
|
I mean how you train the car? My car just keep going randomly lol. 😂😂 |
|
I manage to stream 15 to 20 frame per second |
|
Run collect training data.py
To collect your images
Then run training
Then u can run rc driver
…On Sat 23 Mar, 2019, 19:10 kxrf97, ***@***.***> wrote:
I mean how you train the car? My car just keep going randomly lol. 😂😂
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJurnUowqACG_FsmGdMwBMF6b3c-dpks5vZi7jgaJpZM4Sre9H>
.
|
|
Yaaa after i trained, and run rc driver, my car cant successfull navigate within the track |
|
Accuracy ??
…On Sat 23 Mar, 2019, 19:18 kxrf97, ***@***.***> wrote:
Yaaa after i trained, and run rc driver, my car cant successfull navigate
within the track
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJut2OCElbj_rTZ1inRGs1J9aMgg1cks5vZjCagaJpZM4Sre9H>
.
|
|
Around 70, how many data u collect from a single short track |
|
200+
…On Sat 23 Mar, 2019, 19:23 kxrf97, ***@***.***> wrote:
Around 70, how many data u collect from a single short track
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJulioZ9UVv69WQTNRlucrrUNXKuGCks5vZjHsgaJpZM4Sre9H>
.
|
|
Accuracy? |
|
89+
…On Sat 23 Mar, 2019, 19:55 kxrf97, ***@***.***> wrote:
Accuracy?
—
You are receiving this because you were mentioned.
Reply to this email directly, view it on GitHub
<#77 (comment)>,
or mute the thread
<https://github.com/notifications/unsubscribe-auth/AgOJumWDN9ODU5ejT-qSFlnyAw_Z7PsDks5vZjk9gaJpZM4Sre9H>
.
|
|
Is your project completed? @Gooose1909 |
still getting an error of cannot assingn requested address while running test_stream_server in computer linux |
|
@Gooose1909 could you please contact me on my e-mail : [email protected] |
I get too much delay during streaming of video a lag of about 20sec i use vncserver chrome extension is there any other way to stream or changes to make the delay small
The text was updated successfully, but these errors were encountered: